Schaneider LTMR27MBD ModBus Motor Management System 13.5 – 27A

Rp21.312.000

Main Specification

• TeSys range
• TeSys T product name
• LTMR device short name
• Motor controller product type
• Equipment monitoring and control device application
• 13.5 – 27A measurement current
• 24 V DC rated supply voltage
• 56…127 mA current consumption
• 20.4…26.24 V DC supply voltage limits
• Modbus TCP/EtherNet/IP communication port protocol
• Bus type:
  • Profibus DP polarised 2-wire RS485 interface, addressing 1…125, transmission rate 9.6 kbit/s…12 Mbit/s, SUB-D 9 with 2 shielded twisted pairs, type A
  • Profibus DP polarised 2-wire RS485 interface, addressing 1…125, transmission rate 9.6 kbit/s…12 Mbit/s, terminal block with 2 shielded twisted pairs, type A
• Rated insulation voltage 690 V conforming to:
  • EN/IEC 60947-1
  • CSA C22.2 No 14
  • UL 508
• Rated impulse withstand voltage:
  • 6 kV current or voltage measurement circuit conforming to EN/IEC 60947-4-1
  • 0.8 kV communication circuit conforming to EN/IEC 60947-4-1
  • 0.8 kV supply, inputs and outputs conforming to EN/IEC 60947-4-1
• 100 kA short-circuit withstand conforming to EN/IEC 60947-4-1
• Associated fuse rating:
  • 4 A gG for output
  • 0.5 A gG for control circuit
• Protection type:
  • Load fluctuation
  • Reverse polarity protection
  • Locked rotor
  • Thermal protection
  • Overload (long time)
  • Overload
  • Power factor variation
  • Earth-leakage protection
  • Thermal overload protection
  • Phase unbalance
  • Phase failure

Complementary

• Network and machine diagnosis type:
  • Trip context information
  • Event recording
  • Waiting time after overload tripping
  • Running hours counter/operating time
  • Remaining operating time before overload tripping
  • Fault recording
  • Motor control command recording
  • Trip history information
  • Phase fault and earth fault trip counters
  • Starting current and time
• 6 logic input number
• 7 mA input current
• Logic input current state 0 guaranteed: < 5 V and <= 15 mA for 5 ms
• Logic input current state 1 guaranteed: < 15 V and 2…15 mA for 15 ms
• 2 Hz maximum output switching frequency
• Load current:
  • 5 A at 250 V AC for logic output
  • 5 A at 30 V DC for logic output
• Permissible power:
  • 480 VA (AC-15), Ie = 2 A, 500000 cycles (output)
  • 30 W (DC-13), Ie = 1.25 A, 500000 cycles (output)
• 1800 cyc/h maximum operating rate
• Contacts type and composition:
  • 1 NO + 1 NC fault signal
  • 3 NO
• Metering type:
  • Imbalance current
  • Temperature
  • Average current Iavg
  • Phase current I1, I2, I3 RMS
  • Earth-fault current
• Measurement accuracy:
  • 5…15 % earth fault current internal measurement
  • 1 % voltage (100…830 V)
  • 3 % power factor
  • 5 % earth fault current external measurement
  • +/- 30 min/year internal clock
  • 0,02 temperature
  • 5 % active and reactive power
  • 0,02 current
• Overvoltage category III
• 5.08 mm connection pitch
• Control circuit: connector 1 cable(s):
  • 0.25…2.5 mm² (AWG 24…AWG 14) flexible with cable end
  • 0.2…2.5 mm² (AWG 24…AWG 14) flexible without cable end
  • 0.25…2.5 mm² (AWG 24…AWG 14) flexible without cable end
  • 0.2…2.5 mm² (AWG 24…AWG 14) solid without cable end
• Control circuit: connector 2 cable(s):
  • 0.2…1 mm² (AWG 24…AWG 14) flexible with cable end
  • 0.2…1.5 mm² (AWG 24…AWG 14) flexible without cable end
  • 0.5…1.5 mm² (AWG 24…AWG 14) flexible without cable end
  • 0.2…1 mm² (AWG 24…AWG 14) solid without cable end
• Control circuit tightening torque at 0.5…0.6 N.m flat screwdriver 3 mm

Environment

• Electromagnetic compatibility:
  • Electrostatic discharge, 3, 8 kV air, 6 kV contact, conforming to EN/IEC 61000-4-2
  • Radiated RF fields, 3, 10 V/m, conforming to EN/IEC 61000-4-3
  • Fast transients immunity test (other circuits), level 3, 2 kV, conforming to EN/IEC 61000-4-4
  • Fast transients immunity test (on supply and relay outputs), level 4, 4 kV, conforming to EN/IEC 61000-4-4
  • Voltage dips and interruptions immunity test, 70 %, 500 ms, conforming to EN/IEC 61000-4-11
  • Conducted RF disturbances, 10 V, conforming to EN/IEC 61000-4-6
  • Temperature sensor: surges (serial mode), 0.5 kV, conforming to EN/IEC 61000-4-5
  • Temperature sensor: surges (common mode), 1 kV, conforming to EN/IEC 61000-4-5
  • Control circuit: surges (serial mode), 1 kV, conforming to EN/IEC 61000-4-5
  • Control circuit: surges (common mode), 1 kV, conforming to EN/IEC 61000-4-5
  • Communication: surges (common mode), 2 kV, conforming to EN/IEC 61000-4-5
  • Relay outputs and supply: surges (serial mode), 2 kV, conforming to EN/IEC 61000-4-5
  • Relay outputs and supply: surges (common mode), 4 kV, conforming to EN/IEC 61000-4-5
• Web server services
• Standards:
  • CSA C22.2 No 14
  • EN 60947-4-1
  • IACS E10
  • IEC 60947-4-1
  • UL 508
• Product certifications:
  • CCC
  • BV
  • KERI
  • C-Tick
  • GL
  • ATEX
  • RINA
  • CSA
  • EAC
  • UL
  • NOM
  • DNV
  • LROS (Lloyds register of shipping)
  • ABS
  • RMRoS
• Protective treatment:
  • 12 x 24 hour cycles conforming to EN/IEC 60068-2-30
  • 48 h conforming to EN/IEC 60070-2-11
  • TH conforming to EN/IEC 60068
• Fire resistance:
  • 650 °C conforming to EN/IEC 60695-2-12
  • 960 °C conforming to UL 94
• -20…60 °C ambient air temperature for operation
• -40…80 °C ambient air temperature for storage
• Operating altitude <= 2000 m without derating
• Mechanical robustness:
  • Vibrations mounted on symmetrical rail: 1 Gn, 5…300 Hz conforming to EN/IEC 60068-2-6
  • Vibrations plate mounted: 4 Gn, 5…300 Hz conforming to EN/IEC 60068-2-6
  • Shocks half sine wave acceleration: 15 Gn for 11 ms conforming to EN/IEC 60068-2-27
• IP20 from IP degree of protection

Out of stock

Schaneider LTMR27MBD ModBus Motor Management System 13.5 – 27A TeSys T

Schaneider LTMR27MBD ModBus Motor Management System 13.5 – 27A

SKU: LTMR27MBD Category: Uncategorized